LMN Datasheet, LMN National Semiconductor Voltage Comparator Datasheet, buy LMN. The LM, LM, LM are voltage comparators that have low input currents. They are also designed to operate over a wide range of. Part, LMN. Category. Description, Voltage Comparators. Company, ST Microelectronics, Inc. Datasheet, Download LMN datasheet. Cross ref.

Author: Mikanos Zulkigar
Country: Iran
Language: English (Spanish)
Genre: Technology
Published (Last): 3 October 2014
Pages: 270
PDF File Size: 12.10 Mb
ePub File Size: 19.34 Mb
ISBN: 868-1-48851-824-9
Downloads: 16800
Price: Free* [*Free Regsitration Required]
Uploader: Nijas

Message 5 of 5. You can refer the other possible circuits from the LM datasheet given at bottom. I tried adding in a transistor with a 1k resistor to ground and a TTL signal at the base as per the datasheet and this doesn’t disable the output either.

Message 2 of 5. I expect the output to oscillate between 0 and 1 at the “zero crossing” of the signal.

Submitted by dqtasheet on 6 March As grounding unused pins is a practice on electronics, I guess it was the way of the designer to make sure the device was not disabled for a ground wired to that pin. LMN Comparator with Strobe.

Multisim and Ultiboard

Message 3 of 5. Could the component model be the issue? Any help is appreciated.

Message 1 of 5. TL — Programmable Reference Voltage. An Emitter Output Circuit is shown below. All of those comparator outputs should be a high state datashewt means the LED will turn on connected through the 1K resistor to Vcc.

  AX4SPE-UN MANUAL PDF

Most Active Software Boards: This pin is connected to the ground of the system Negative voltage can also be used. The output is correct as seen on the scope.

The problem is that tying the strobe pin to ground should make the output stop changing, and it isn’t. I just built the circuit in real life and it works exactly as I thought, putting GND on the strobe pin makes the output a constant state at Vcci.

Why is it not working in Multisim?

LM Datasheet and Product Info | Analog Devices

The transistor can also make the Load to be isolated from the system ground, so if you are looking for a Voltage comparator to drive loads of these specifications then this IC might be the right choice for you. The LM can work on a Single supply voltage or in a dual supply mode.

Message 4 of 5. The pins 5 and 6 on the Op-amp are used to set the balance voltage if you want to manually adjust the DC-Offset voltage. A sample circuit is shown below in which the Inverting Terminal is set to 2. When not in use the pins 5 and 6 should be shorted as shown above.

LM Pinout, Pin Configuration, Specifications, Equivalent, Working & Datasheet

Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. The simplified schematics of the IC is shown below: The problem is that the strobe pin is not working for the model. I built a simple circuit using the LMN comparator. You can note that the Output voltage stays high when pin 2 has higher voltage than pin 7 and vice versa.

  ENVIRONMENTAL STUDIES BY DEEKSHA DAVE PDF

Attached is a Multisim file with every comparator with a strobe feature available in Multisim and a picture of the circuit. If the voltage at the Non-Inverting Terminal pin 2 is higher than the Inverting Terminal pin 2the output pin 7 will also be high else the output will be low.

The simplified schematics of the IC is shown below:.

Normally these pins are not used since the Input Offset itself is much better controlled. Any Op-Amp can be made to work as a voltage comparator, but the LM proves itself to be advantages by housing an Output Transistor inside its package.

According to the datasheet, if you tie the strobe pin to GND then the output should be disabled.