Model: A. Manufacturer: Fluke. About: We are NES Sales, Northeast’s industrial source. Notes: Does not include stand. Sold as-is, as pictured. | eBay!. Fluke A bench multimeter. «on: November 04, , am». I got this oldie from ebay the other day, the seller sold it as untested but it works. Fluke will not be liable for any claims, losses or damages of any kind incurred by any user arising from use of this manual. A Digital Multimeter Instruction.

Author: Tunos Dizilkree
Country: Uganda
Language: English (Spanish)
Genre: Spiritual
Published (Last): 25 January 2008
Pages: 348
PDF File Size: 3.95 Mb
ePub File Size: 5.61 Mb
ISBN: 882-2-82721-158-2
Downloads: 86846
Price: Free* [*Free Regsitration Required]
Uploader: Yozshurg

The battery pack should now be restored to its rated capacity. The input current is applied across a portion 8600s the shunt resistor network via contacts of the selected range switch. The offset voltage reference is protected from over- voltage conditions by Q8 and Q9.

Operating power for the probe is provided by an internal lithium battery. Remove the instrument from tluke case. Manchester, NH Oitronics, Inc. First check the signal at the gate of the FET.

Fluke 8600A FOR RENT

Learn More – opens in a new window or tab Any international shipping is paid in part to Pitney Bowes Inc. The total charge time is approximately 16 hours.

Deluxe Test Lead Kit A80 When the digit count exceeds the display capacity pin 6 of the DOU output connector changes from a logic 0 to logic 1. Therefore the time required to discharge C28 is propor- tional to the voltage from the input divider.

  HALLUCINOGENS AND CULTURE FURST PDF

AC Converter Relay Operation 4- 1.

This section contains an illustrated parts breakdown of the instrument. Use the procedure which corresponds to the model number of the kit being installed. Please reference the instrument model number when requesting a new shipping container. Capacitor Cl is used The contaminants on printed circuit boards can first be loosened by spraying them with Freon T.

Sold as-is, as pictured.

Rent Fluke A Digital Multimeter 4 1/2 Digit | Transcat

Note the amplitude of the signal; it should be 2. Remove the ac converter pcb, take the metal shield off the side and reinstall the board into mainframe. Box Beijing Tel: Parts lists include the following information: The amount of current required by Q3 is constant in all operating conditions. Calibration Adjustment Locations 44 New data will start to load into the DOU after the next measurement is complete.

Sub of Raytheon Co.

The numerical value of each digit of the instrument display is presented in a four-bit bed format at the DOU output connector. Add to watch list. The presence of an overrange indication does not necessarily mean that the instrument is being exposed to a damaging input condition.

Digital Multimeter 8600A

ST5 clocks the data into U The voltage level should be the same as that noted in step e. High Frequency Probe 8600z RF If absent or wrong, check that output from U8, keeping in mind that 8600s driver transistors act as inverters. The connector pin assignments for each significant digit of the display are provided in Table Allow the battery pack to discharge for 30 hours, then charge the battery pack at twice the discharge rate for 20 hours.

  BITSCH TROMBONE ETUDES PDF

The following circuit descriptions are keyed to the functional fluoe defined in the overall functional block diagram of Figure The output of U5 is applied to the input of comparator, U6.

Teflon or vinyl insulated wire, 26 gauge, 3 1 pieces cut to the desired length. Box C, Everett, Washington Rev.

The DOU provides a single-bit output indication of a display overload condition. Learn More – opens in a new window or tab. Ten volts is maintained across the input divider in all ranges except the 20 range. The output of U4 is applied to the inverting input of integrator, U5. Cleveland, OH Verbatim Corp. Refer to eBay Return policy for more details. The converter then changes the ac input to an equivalent dc voltage for the mV and 2V ranges.

Cleveland, OH Product Comp. If the dc input voltage is increased to 2V, the stable portion of the waveform should be msec long.